Investigation of the strength property of 3D printed products in bending deformation to optimize material distribution
https://doi.org/10.25206/1813-8225-2025-193-30-37
EDN: MVIKFZ
Abstract
The article considers a method of optimal material distribution inside a 3D printed sample. Several variants of material distribution are considered, including the beam shape of equal resistance while retaining the outer frame of the specimen as a rectangular parallelepiped with a square cross-section. The manufactured samples are subjected to destruction during static bending testing. The results show the reduction of used material by 30 % and preservation of specimen strength properties with 100 % material filling. Moreover, experimental results are presented and research issues for further investigations are highlighted.
About the Authors
A. V. Shimokhin
Omsk State Agrarian University
Russian Federation
Russian Federation
SHIMOKHIN Anton Vladimirovich, Candidate of Economics Sciences, Associate Professor, Associate Professor of the Technical Service, Mechanics and Electrical Engineering Department
AuthorID (RSCI): 700145
AuthorID (SCOPUS): 57203345154
ResearcherID: ACS-9917-2022
Omsk
A. N. Sorokin
Omsk State Agrarian University
Russian Federation
Russian Federation
SOROKIN Anatoly Nikiforovich, Candidate of Technical Sciences, Associate Professor, Associate Professor of the Technical Service, Mechanics and Electrical Engineering Department
AuthorID (RSCI): 714190
AuthorID (SCOPUS): 57209773219
Omsk
S. N. Boltovsky
Omsk State Agrarian University
Russian Federation
Russian Federation
BOLTOVSKY Sergey Nikolaevich, Senior Lecturer of the Technical Service, Mechanics and Electrical Engineering Department
AuthorID (RSCI): 1068092
AuthorID (SCOPUS): 57203345154
ResearcherID: ACS-9917-2022
Omsk
V. N. Kuznetsova
Siberian State Automobile and Highway University
Russian Federation
Russian Federation
KUZNETSOVA Victoria Nikolaevna, Doctor of Technical Sciences, Professor, Professor of the Operation of Oil, Gas and Construction Equipment Department
AuthorID (RSCI): 1068092
Omsk
I. S. Kuznetsov
Siberian State Automobile and Highway University
Russian Federation
Russian Federation
KUZNETSOV Ilya Sergeevich, Senior Lecturer of the Operation of Oil, Gas and Construction Equipment Department
AuthorID (RSCI): 1068092
Omsk
References
1. Ozerov A. Topologicheskaya optimizatsiya i 3D-pechat′ kak primer vzaimnogo razvitiya. QIB Tehnologies [Topological optimization and 3D-printing as examples of cross-development]. URL: https://blog.iqb.ru/topology-optimization-3d-printing/ (accessed: 07.07.2024). (In Russ.).
2. Antsiferov S. I., Karachevtseva A. V., Sychev E. A., Litvishko A. A. Topologicheskaya optimizatsiya elementov konstruktsii robotizirovannoy yacheyki [Topological optimization of design elements of a robotic cell]. Vestnik Belgorodskogo gosudarstvennogo tekhnologicheskogo universiteta im. V. G. Shukhova. Bulletin of Belgorod State Technological University Named after V. G. Shukhov. 2023. No. 11. P. 93–102. DOI: 10.34031/2071-7318-2023-8-11-93-102. EDN: FODJWS. (In Russ.).
3. Russkikh G. S., Shalygin S. V. Algoritm formirovaniya vnutrenney struktury izdeliya s uchetom napryazhennodeformirovannogo sostoyaniya na primere trekhtochechnogo izgiba [The algorithm for generating internal structure of product considering stress-strain on example three-point bending]. Omskiy nauchnyy vestnik. Seriya Aviatsionno-raketnoye i energeticheskoye mashinostroyeniye. Omsk Scientific Bulletin. Series Aviation-Rocket and Power Engineering. 2021. Vol. 5, no. 1. P. 80–85. DOI: 10.25206/2588-0373-2021-5-1-80-85. EDN: TXWRGA. (In Russ.).
4. Kondratov S. V., Pykhtin A. A., Larionov S. A., Sorokin A. E. Vliyaniye tekhnologicheskikh rezhimov FDM-pechati i sostava ispol′zuyemykh materialov na fiziko-mekhanicheskiye kharakteristiki FDM-modeley (obzor) [Influence of the technological FDM-modes of the press and structure of used materials on physic-mechanical characteristics of FDM-models (review)]. Trudy VIAM. Proceedings of VIAM. 2019. No. 10 (82). P. 34–49. DOI: 10.18577/2307-6046-2019-0-10-34-49. EDN: RARUXZ. (In Russ.).
5. Shimokhin A. V., Soyunov A. S., Bitkina E. E., Yankovskiy K. A. K voprosu o primenenii additivnoy tekhnologii na predpriyatiyakh sel′skokhozyaystvennogo mashinostroyeniya [On applicability of additive technology at agricultural engineering enterprises]. Traktory i sel′khozmashiny. Tractors and Agricultural Machinery. 2022. Vol. 89, no. 5. P. 357–365. DOI: 10.17816/0321-4443-111103. EDN: KPBBLF. (In Russ.).
6. Petrova G. N., Platonov M. M., Bol′shakov V. A. [et al.]. Issledovaniye kompleksa kharakteristik bazovykh materialov dlya FDM-tekhnologii additivnogo sinteza. Fiziko-mekhanicheskiye i teplofizicheskiye svoystva [Research of the complex of characteristics of base materials for fdm of technology of the additive synthesis. physico-mechanical and heat-physical properties]. Plasticheskiye massy. Plasticheskie Massy. 2016. No. 5–6. P. 53–58. EDN: WIOBNL. (In Russ.).
7. Kovalenko R. V. Sovremennyye polimernyye materialy i tekhnologii 3D pechati [Modern polymer materials and 3D printing technologies]. Vestnik Tekhnologicheskogo universiteta. Herald of Technological University. 2015. Vol. 18, no. 1. P. 263–266. EDN: TJKZCT. (In Russ.).
8. Kichko A. E. Analiz sovremennykh materialov dlya 3D-pechati [Analysis of modern 3D printing materials]. 72-ya Mezhdunar. stud. nauch. tekhn. konf. Astrakhan’, 2022. P. 758–760. EDN: SRYIOG. (In Russ.).
9. GOST 4648-2014 (ISO 178:2010). Plastmassy. Metod ispytaniya na staticheskiy izgib [Plastics. Method of static bending test]. Moscow, 2016. 20 p. (In Russ.).
10. Bogdanov V. V., Ivanov R. V. K voprosu ispol′zovaniya balok ravnogo soprotivleniya izgibu s peremennym poperechnym secheniyem [To the question of use of equal bending resistance beams with variable cross-sections]. Aktual’nyye problemy nauki i obrazovaniya v usloviyakh sovremennykh vyzovov. Moscow, 2022. P. 228–234. (In Russ.).
11. Kuzubov A. S., Bushuev D. A., Parashchuk E. M. Postroyeniye i validatsiya konechno-elementnoy virtual’noy modeli balki ravnogo soprotivleniya vesoizmeritel’noy sistemy [Construction and validation of the finite element virtual model of the beam of equal resistance of the weight measuring system]. Nauchnyye vedomosti Belgorodskogo gosudarstvennogo universiteta. Seriya: Ekonomika. Informatika. Belgorod State University. Scientific Bulletin. Series: Economics. Information Technologies. 2019. Vol. 46, no. 2. P. 274–282. DOI: 10.18413/2411-3808-2019-46-2-274-282. EDN: JPWOJO. (In Russ.).
Review
For citations:
Shimokhin A.V., Sorokin A.N., Boltovsky S.N., Kuznetsova V.N., Kuznetsov I.S. Investigation of the strength property of 3D printed products in bending deformation to optimize material distribution. Omsk Scientific Bulletin. 2025;(1):30-37. (In Russ.) https://doi.org/10.25206/1813-8225-2025-193-30-37. EDN: MVIKFZ
Views:
6
JATS XML
Email this article 